October 9, 2008

How to Make a Great Jewelry Display for Selling

Okay, I have had about half a dozen jewelry displays in my short lifetime and none of them really impressed me or made my jewelry stand out. I even had the opportunity to have nice designer busts and whatnot, which I then spray painted black, thus ruining them. I also don't like felted displays because I have a very large cat, so hair gets everywhere, even in closed spaces.

I really looked high and low for something affordable, portable and pretty to display my jewelry when I am selling and decided to just make my own jewelry displays! I make more earrings than anything, so I was focused on something that could display my earrings in one or two places and not make my table look too junky.

I came up with picture frames! They are in every thrift store, and with my simple instructions, they can make really nice displays for your jewelry. Also, if you really like a frame to something and it's not a picture frame, say a mirror, the instructions are the same.


I actually liked the pattern on this mirror so much, I decided it would make a great display. I got in from Salvo for around $4. Make sure the frame is in good condition, if not, it's okay to use it, you'll just have to take some extra steps in the middle of this how-to. You should also choose a frame that is pretty unique and will have a pattern or dimension that you will be able to see behind a few coats of spray paint.



Here's what you will need:

a picture frame or mirror, whatever size you can handle
1 can of clear varnish
a ruler or measuring tape
wood glue
screw in hooks ( you can get it from metalliferous or a hardwear store )
elmer's wood glue
a drill and drill bit ( a dremmel or flex shaft will work too)
a set of 2lb weights or heavy books
a great pencil
an eraser
spray paint of your color choice
Newspaper, scrap paper
Safety goggles
Pliers
cut wood ( read directions first!)


1. Start with your nice, clean frame. Turn it over and remove the backing, any staples, cardboard and glass. Also, if you have any cracks in the frame, now is the time to glue the pieces with wood glue and set it aside for 24 hours before doing more.

2.After you take the everything off the back of the frame, measure the inside of the frame, as well as the depth, for instance, this frame measures 8x8 in and is 1/4" deep. You can then go to your local lumber yard ( I went to Metropolitan Lumber and Hardware in SoHo, NY) and get a piece of wood cut with the correct dimensions. My piece of wood cost less than a dollar, so this definetely won't break the bank!

3. Next, you will want to make marks on your wood, so you can find out where you will want to put the screw in. I did a graph of quarter inches. It doesn't really matter if you can't get everything really straight, as long as it's pretty lined up, it's okay. Afer you make all your marks, check off where you would like the screws to go. You can put the jewelry you will be displaying on the wood, to make sure you have enough space in between. Then you can mark off in dark X's where you would like to drill.

4. Depending on the size of the screw, make sure that your drill bit is a bit smaller than the size of your screw. Also, depending on the type of jewelry you have, you may want to make the screw go horizontally, or if you choose to make it go vertically, make sure to snip the back part, so the earrings will be easy to take on and off the display.

5. Now, for the fun part! With safety goggles on, carefully drill each X you marked on the wood. Erase the pencil marks that you made on the wood, as you don't need them anymore. Then insert each screw. They should be very snug in the hole. You might need to use pliers to tighten them into the wood.

Next, you 'll want to place the frame face down and apply a good amount of wood glue on the inside. Place the wood with the screws face down on the frame. It will take about 24 hours for the glue to dry completely, so place a few weights or books on the back of the frame and wood, so it can really be bonded.


6. After the glue dries, you're almost done! All you need to do is spray paint the front, sides and back with the color of your choice. Spray a few coats and finish off with a few coats of clear varnish and you're done!

You have a nice jewelry display for selling your wares!

4 comments:

Anonymous said...

That looks great! What do you use for displaying necklaces in a small space?

alicia g - www.linguanigra.com said...

Hi Liz! This can be used in a small space, as it's so flat. I also put frames that don't have easels built in on easels. If you use a larger frame and put it on an easel, that should solve the small-space-display problem !
alicia

Unknown said...

fantastic project...thanks for sharing! I've struggled with the display thing too. Lately, I just lie flat on a mat with earring cards. But now I'm newly inspired....

Anonymous said...

I like this. I've seen others with photo frames but they weren't solid and the view between strips often detracted from the jewelry that was displayed. You can find more display ideas at: http://hubpages.com/hub/Booth-Display-Options there are 4 hubs there on different display. Hope you enjoy!! Teri
http://www.sandtcreations.com/wordpress